QSI 520c Betriebsanweisung Seite 14
- Seite / 87
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
QSI 500 SERIES USER GUIDE
11
Electrical Connections
The image at the left is a close-
up of the bottom of the camera
body. All electrical connections t
the camera are made through t
three connectors located on this
connector panel. The panel is
recessed into the camera body to
protect the connectors when no
cables are attached.
o
he
DC Power Connector
The camera is ordinarily powered by the included AC power adapter which plugs into the
middle connector on the bottom of the camera. The AC power adapter accepts any input
voltage from 90v to 240v and 50-60 Hz. It is supplied with a region-specific AC power cord.
Shortly after power is applied to the camera, the Camera Status Indicator on the back of the
camera will start glowing yellow indicating that the camera is starting up. The camera will
make a small “chirp” sound and then a few seconds later will make a “chirp chirp” sound
indicating that the camera successfully completed its initialization steps. The Camera
Status Indicator will begin flashing green if the camera is not connected via the USB cable.
The Camera Status Indicator will glow solid green once the camera is connected to the
computer via the USB cable. See the Status and Notification discussion later in this
Section for additional detail.
Note: Power-up initialization can take up to 6 seconds. It is not possible to
connect to the camera from the imaging application (MaxIm LE, CCDSoft, etc.)
during this time. Any attempt to do so will cause an error message to be displayed
by your imaging application.
Note: The camera is designed to operate on stable, regulated 12V DC power and
consumes less than 2 amps at full power. DC power input above or below 12V
will decrease the maximum cooling capability of the camera by increasing power
dissipation or lowering cooling efficiency. If the input voltage is below 11V or
above 14V the camera will report an error until the voltage is returned to the
specified range. See Status and Notification below.
Caution: Applying an input voltage over 16V or under 10V may
permanently damage the camera and will void the camera warranty.
- 500 Series User Guide 1
- Table of Contents 2
- Getting Started 4
- What’s In the Box? 5
- Get to Know Your Camera 6
- Install Software and Drivers 7
- Connect the camera 8
- Take an image 10
- QSI 500 SERIES USER GUIDE 11
- Camera Attachment Options 12
- Using SLR Lenses 13
- Electrical Connections 14
- Cooling the Camera 17
- Internal Color Filter Wheel 21
- Advanced Setup Options 22
- Imaging Options 25
- Other Options 25
- Enable Pixel Masking 26
- Status and Notification 28
- CCD Imaging Overview 31
- Interline Transfer CCDs 32
- Anti-Blooming CCDs 32
- Microlenses 33
- Single-shot color CCDs 33
- Signal versus noise 34
- Reducing noise in CCD images 35
- 6-minute Dark Frame 36
- Original image 37
- Flat Fields 37
- Bias Frames 39
- Stacking Images 40
- Color images 41
- Taking Images with your 42
- QSI 500 Series Camera 42
- Camera Control Window 43
- Cool the CCD 45
- Focusing with MaxIm LE 46
- Take a single image 47
- View the image in MaxIm LE 48
- Take a series of images 48
- Image Calibration 50
- Dark Frames 51
- Manual Image Calibration 52
- Scale by Flat Fields 54
- Calibrate Images in MaxIm LE 59
- Combine Frames in MaxIm LE 60
- Combined image of M78 62
- Binning 63
- 384x256 64
- Shutting down your camera 67
- Guiding 68
- Using an AutoGuider 69
- Accessories 74
- SLR lens adapter 75
- Liquid heat exchanger 75
- Recirculating pump 75
- Color filter wheel 75
- Care & Maintenance 76
- Cleaning the color filters 78
- Cleaning the CCD cover glass 78
- Updating the Firmware 78
- Recharging the desiccant 80
- Technical support 81
- C-mount adapter 82
- Model 504 CCD Specifications 83
- Model 516 CCD Specifications 83
- Model 532 CCD Specifications 84
- Model 520 CCD Specifications 84
- Model 540 CCD Specifications 85
- Model 583 CCD Specifications 85
- Appendix B – Warranty 86
Verwandte Produkte und Handbücher für Sicherheitskameras QSI 520c
Sicherheitskameras QSI 516 Betriebsanweisung
(89 Seiten)
(89 Seiten)
Sicherheitskameras QSI 520c Betriebsanweisung
(82 Seiten)
(82 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern